OBD Fusion

Any chance of getting a button to start and stop DataLogging on AppleCar play ?

App is basically worthless on IOS you have to buy specific OBD 2 scanners for it work, and unlike the app says it’s not an IOS issue because the scanner works with other apps.

Been using this app for a few months, while the convenience of being able to check codes immediately on the fly is great, the logging feature is suboptimal with pid poling every 3-4 seconds. Checking fuel trims, maf or o2 sensor voltages is useless and I find myself having to grab a normal scanner as a result. Even with minimal pids selected there is no change to the rate. I really wanted to love this app but for the money for both the Bluetooth dongle and app, better off just getting a decent scanner instead.

It’s very helpful. I know works very well with my car. Hope to get some more add-ons more stuff to your vehicles

Tried connecting to a supported OBD reader and this app wouldn’t connect. Customer support was decent at first but are just following a script. Once we got to the end of the script no further communication Very disappointed

By far the best practical ODB reader out there. This app is a MUST for 2007 - 2012 MINI Cooper owners to monitor the engine temps as the car didn’t come with a temp gauge on the dash. I have one in all my minis (3). Vital. The update is a welcome refresh of the app. I just have a few complaints. I monitor my engine constantly when I drive. I have an old iPhone mounted on my dash that it’s only job is to connect to the BLE device and report engine status. 1. When I stop for gas I want the ability to leave the app running, stop the car, fill up, start the car and the app will reconnect. It currently does not do this. I’m not sure what is happening but I must close the app completely and relaunch for it to reconnect properly. 2. If I minimize the app and stop the motor, then restart it will reconnect but there’s a message that it’s recounting (button cancel) in the middle of the screen. You can clearly see the app has reconnected and it’s reporting data. I simply tap cancel and I’m on my way. Little bit of a pain. 3. Suppress the connection messages. That used to be part of the old app, but since the refresh I have to watch it go through all the protocols until it’s connected. Not a show stopper but could be cleaned up. I just want to launch the app and see the connect button at the bottom change to connected and start reporting data. 3. Save config settings. I would like the ability to export out my dashboard configuration and upload it to a new device. Like I said earlier I have 3 minis running this app and would like the dashboards all the same. I know I could go in and make them all the same manually but if you’ve ever been in the dash configuration menu you’ll know it can be clunky to do this. I would love the ability to make one dash the way I want and then clone it to the others. That’s it, great app, use it everyday when I drive without fail.

Works great on Lexus rx

I bought diagnostic for Nissan and after I got a new car (Mazda) I have to buy it again. Will never use this OBD again and gonna buy a different one with a free diagnostic

I purchased OBD Fusion and the Ford enhanced diagnostics based on the developers claim of supporting and displaying mode $06 data. Don’t waste your money if you expect to get a full view of all the $06 data. The app only shows one or two PIDs and lists as ‘manufacturer defined’. Nothing else. A full hex listing would be easy to do. The Ford enhanced diagnostics for my 1996 model are not complete either. I have the OEM PCM manuals to cross reference and many are missing from the app. The 14.99 up charge for this data is a rip off. A simple example is the cylinder misfire counts. My vehicle has 8 cylinders yet OBDfusion lists only cylinder 1-6 misfire count as available PIDs. Unbelievable. The vehicle data shows 8 cylinders right on the app so they know what should be there. Learn from my mistake and spend the money to get a pro scan tool that actually shows the data.

In reality when you use it in CarPlay just a few lines show up. No dashboards or gages. Would. It have purchased if that was disclosed.