Расшифруйте показание 11/15
Расшифруйте показание 11/15 на регулировочных винтах низкого и высокого. Ни где нет информации
Jetting for IAME kart engines
Setup X30, Super X30 & Leopard
Разработчик: Ingenieria del Software ISEnet S.L
Описание
This app provides, for the current weather conditions and a given engine configuration (engine model, gas, etc.), a jetting and exhaust length recommendation for IAME Parilla X30 Senior or Junior (Tillotson & Tryton carbs), X30 Super 175cc & Leopard engines.
In order to get the weather values, the application can use the GPS to obtain the position and altitude, and the network connection to get the temperature, pressure and humidity from the nearest weather station. Nevertheless, the application can run without GPS and internet connection, in this case, the user has to give the weather data.
The application is made up of four tabs that are described next.
- Results: In this tab, a recommended jetting and exhaust length setup are shown. These data are calculated depending on the weather conditions and the engine and track configuration given in the following tabs. The following values are given: high needle, low needle, pop-off pressure and exhaust length. Besides this information, the air density and density altitude are shown too. In addition, this tab lets do a fine tunning adjustment for the high and low needles to adapt to the concrete engine.
- Weather: In the second tab, called Weather, you can set the values for current temperature, pressure, altitude and humidity. The values of this screen can be manually set or can be loaded by the application reading the data from the nearest weather station (from the GPS tab).
- Engine: You must set in this screen the information about the engine, that is, the engine type (Leopard, X30 Senior, X30 Junior X30 Super), carburetor, exhaust restrictions (for Junior engines), the oil mix ratio and the type of the circuit (short or long tracks). Depending of the track type, the jetting setups will be adapted.
- GPS: This tab allows to use the GPS to get the current position and altitude, and connect to an external service to get the weather conditions of the nearest weather station (temperature, pressure and humidity).
The application works with different measure units: inHg, mb, mmHg, hPa, atm for pressure, ºC and ºF for temperature.
Hide
Показать больше...
In order to get the weather values, the application can use the GPS to obtain the position and altitude, and the network connection to get the temperature, pressure and humidity from the nearest weather station. Nevertheless, the application can run without GPS and internet connection, in this case, the user has to give the weather data.
The application is made up of four tabs that are described next.
- Results: In this tab, a recommended jetting and exhaust length setup are shown. These data are calculated depending on the weather conditions and the engine and track configuration given in the following tabs. The following values are given: high needle, low needle, pop-off pressure and exhaust length. Besides this information, the air density and density altitude are shown too. In addition, this tab lets do a fine tunning adjustment for the high and low needles to adapt to the concrete engine.
- Weather: In the second tab, called Weather, you can set the values for current temperature, pressure, altitude and humidity. The values of this screen can be manually set or can be loaded by the application reading the data from the nearest weather station (from the GPS tab).
- Engine: You must set in this screen the information about the engine, that is, the engine type (Leopard, X30 Senior, X30 Junior X30 Super), carburetor, exhaust restrictions (for Junior engines), the oil mix ratio and the type of the circuit (short or long tracks). Depending of the track type, the jetting setups will be adapted.
- GPS: This tab allows to use the GPS to get the current position and altitude, and connect to an external service to get the weather conditions of the nearest weather station (temperature, pressure and humidity).
The application works with different measure units: inHg, mb, mmHg, hPa, atm for pressure, ºC and ºF for temperature.
Скриншоты
Jetting for IAME kart engines Частые Вопросы
-
Приложение Jetting for IAME kart engines бесплатное?
Да, Jetting for IAME kart engines полностью бесплатное и не содержит встроенных покупок или подписок.
-
Является ли Jetting for IAME kart engines фейковым или мошенническим?
Недостаточно отзывов для надежной оценки. Приложению нужно больше отзывов пользователей.
Спасибо за ваш голос -
Сколько стоит Jetting for IAME kart engines?
Приложение Jetting for IAME kart engines бесплатное.
-
Сколько зарабатывает Jetting for IAME kart engines?
Чтобы получить оценку дохода приложения Jetting for IAME kart engines и другие данные AppStore, вы можете зарегистрироваться на платформе мобильной аналитики AppTail.
Оценки пользователей
Приложение еще не оценено в Чехия.
История оценок
Jetting for IAME kart engines Отзывы Пользователей
Оценки
История позиций в топах
История рейтингов пока не доступна
Позиции в категории
|
Рейтинг
|
Категория
|
Позиция
|
|---|---|---|
|
Топ платных
|
|
17
|
|
Топ платных
|
|
21
|
|
Топ платных
|
|
34
|
|
Топ платных
|
|
62
|
|
Топ платных
|
|
86
|
Jetting for IAME kart engines Конкуренты
| Name | Отзывы | Оценки | Последнее обновление | |
|---|---|---|---|---|
Jetting for TM KZ / ICC Kart
for KZ-R1, KZ10, K9 engines
|
1
|
|
2 года назад | |
Jetting IAME KZ1 / KZ2 Kart
Screamer 1, 2, 3 and Shifter
|
0
|
|
2 года назад | |
Jetting for IAME X30 Karting
for X30, Super X30 & Leopard
|
0
|
|
2 года назад | |
Kart Chassis Setup PRO
karting tools for racers
|
1
|
|
2 года назад | |
Jetting IAME SWIFT & GAZELLE
get best carburetor config
|
0
|
|
2 года назад | |
Jetting TM Racing OK & OK-J
best carburetor config S1 & S2
|
0
|
|
2 года назад | |
Jetting Vortex ROK GP Kart
get best carburetor config
|
0
|
|
2 года назад | |
Jetting IAME KA100 & KFS FFSA
get best carburetor config
|
0
|
|
2 года назад | |
Jetting Vortex OK & OK-Junior
get best carburetor config
|
0
|
|
2 года назад | |
Jetting IAME OK OK-Junior Kart
best carb config for Reedster
|
0
|
|
2 года назад |
Jetting for IAME kart engines Установки
Last 30 days
Jetting for IAME kart engines Доход
Last 30 daysJetting for IAME kart engines Доходы и Загрузки
Получите ценные инсайты о производительности Jetting for IAME kart engines с помощью нашей аналитики.
Зарегистрируйтесь сейчас, чтобы получить доступ к статистика загрузок и доходов и многому другому.
Зарегистрируйтесь сейчас, чтобы получить доступ к статистика загрузок и доходов и многому другому.
Информация о приложении
- Категория
- Sports
- Разработчик
-
Ingenieria del Software ISEnet S.L
- Языки
- Portuguese, German, Czech, Chinese, Korean, Danish, Slovak, Spanish, Finnish, French, Greek (modern), Hebrew (modern), Dutch, Hungarian, Indonesian, English, Italian, Japanese, Malay, Norwegian Bokmål, Polish, Romanian, Swedish, Thai, Turkish, Ukrainian, Vietnamese, Arabic
- Последнее обновление
- 1.7 (11 месяцев назад )
- Выпущено
- Nov 10, 2015 (8 лет назад )
- Также доступно в
- Пакистан, Италия, Япония, Республика Корея, Кувейт, Казахстан, Ливан, Мексика, Малайзия, Нигерия, Нидерланды, Норвегия, Новая Зеландия, Перу, Филиппины, Индия, Польша, Португалия, Румыния, Россия, Саудовская Аравия, Швеция, Сингапур, Таиланд, Турция, Тайвань, Украина, Соединенные Штаты, Вьетнам, Южно-Африканская Республика, Дания, Аргентина, Австрия, Австралия, Азербайджан, Бельгия, Бразилия, Беларусь, Канада, Швейцария, Чили, Китай, Колумбия, Чехия, Германия, ОАЭ, Доминиканская Республика, Алжир, Эквадор, Египет, Испания, Финляндия, Франция, Великобритания, Греция, Гонконг (САР), Венгрия, Индонезия, Ирландия, Израиль
- Обновлено
- 1 месяц назад
AppTail.